rini:to-do_2011
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
|
rini:to-do_2011 [2011/04/11 03:21] ben [Bottom painting supplies] |
rini:to-do_2011 [2011/04/11 04:49] ben [Completed] |
||
|---|---|---|---|
| Line 1: | Line 1: | ||
| - | ==== Bottom painting supplies ==== | ||
| - | Bottom painting, done. | ||
| - | |||
| - | * <del>masks</del> | ||
| - | * <del>gloves</del> | ||
| - | * <del>scrapers</del> | ||
| - | * <del>masking tape</del> | ||
| - | * <del>drop cloths</del> | ||
| - | * <del>containers to mix epoxy paint (that won't melt, tin cans maybe)</del> | ||
| - | * <del>sand paper</del> | ||
| - | * <del>sanding blocks</del> | ||
| - | * <del>beer</del> | ||
| - | * <del>bourbon</del> | ||
| ==== Misc Info ==== | ==== Misc Info ==== | ||
| Line 32: | Line 19: | ||
| === Mast === | === Mast === | ||
| - | + | * New Windex | |
| - | * <del>Remove lost/dropped halyard blocks from center of mast</del> DONE! | + | |
| - | * <del>Either get 12-20 screws for spreaders or drill out to MM size</del> Drilled and tapped to M6! | + | |
| * Replace masthead lamp with LED | * Replace masthead lamp with LED | ||
| * Install baton to lift backstay over sail headboard when tacking? | * Install baton to lift backstay over sail headboard when tacking? | ||
| Line 48: | Line 33: | ||
| === Hull === | === Hull === | ||
| - | * <del>Patch small paint crack just above water line on starboard side near stern</del> | + | * <del>Sand and</del> varnish tiller, needs two more coats |
| * Replace toe-rails | * Replace toe-rails | ||
| * Replace hatch-cover | * Replace hatch-cover | ||
| * Install external hatch handle | * Install external hatch handle | ||
| * Replace wood underneath spinnaker barber-haul cleats | * Replace wood underneath spinnaker barber-haul cleats | ||
| - | * <del>Check rudder bearings and shaft condition</del> Should be okay for a long time to come. | ||
| - | * <del>Bottom</del> | ||
| * Reattach (replace?) cockpit floorboards | * Reattach (replace?) cockpit floorboards | ||
| - | * <del>Sand and</del> varnish tiller, needs two more coats | ||
| * Patch random cracks on deck & in cockpit | * Patch random cracks on deck & in cockpit | ||
| Line 78: | Line 60: | ||
| ==== Completed ==== | ==== Completed ==== | ||
| * Weld tiller bracket back together | * Weld tiller bracket back together | ||
| + | |||
| + | === Hull === | ||
| + | |||
| + | * <del>Patch small paint crack just above water line on starboard side near stern</del> | ||
| + | * <del>Check rudder bearings and shaft condition</del> Should be okay for a long time to come. | ||
| + | * <del>Bottom paint</del> | ||
| + | |||
| + | === Mast === | ||
| + | |||
| + | * <del>Remove lost/dropped halyard blocks from center of mast</del> DONE! | ||
| + | * <del>Either get 12-20 screws for spreaders or drill out to MM size</del> Drilled and tapped to M6! | ||
| + | |||
| + | ==== Bottom painting supplies ==== | ||
| + | |||
| + | * <del>masks</del> | ||
| + | * <del>gloves</del> | ||
| + | * <del>scrapers</del> | ||
| + | * <del>masking tape</del> | ||
| + | * <del>drop cloths</del> | ||
| + | * <del>containers to mix epoxy paint (that won't melt, tin cans maybe)</del> | ||
| + | * <del>sand paper</del> | ||
| + | * <del>sanding blocks</del> | ||
| + | * <del>beer</del> | ||
| + | * <del>bourbon</del> | ||
rini/to-do_2011.txt · Last modified: 2011/04/28 04:18 by ben
Page Tools
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Noncommercial-Share Alike 3.0 Unported
