This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision | ||
rini:iw31 [2011/07/10 04:43] ben |
rini:iw31 [2013/03/24 09:14] ben removed |
||
---|---|---|---|
Line 1: | Line 1: | ||
- | Links: | + | ====== Links: ====== |
http://www.skipperguide.de/wiki/Hallands_Väderö | http://www.skipperguide.de/wiki/Hallands_Väderö | ||
Line 26: | Line 26: | ||
http://www.iw31.dk/ | http://www.iw31.dk/ | ||
+ | |||
+ | http://www.iwrig.com/57718625 | ||
http://eskapad.wordpress.com/ | http://eskapad.wordpress.com/ | ||
Line 40: | Line 42: | ||
http://www.marinepartseurope.com/en/volvo-penta-explodedview-7726000-30-11707.aspx | http://www.marinepartseurope.com/en/volvo-penta-explodedview-7726000-30-11707.aspx | ||
+ | ====== docs ====== | ||
volvo instrument panel parts: | volvo instrument panel parts: | ||
Line 74: | Line 77: | ||
19 CABLES AND TERMINALS | 19 CABLES AND TERMINALS | ||
</code> | </code> | ||
+ | |||
+ | https://www.marinestore.nl/Navigatie_Stuurkompassen/c216_222/p2000001482/Danforth/Constellation_C561_HA/product_info.html | ||
+ | https://www.marinestore.nl/Navigatie_Stuurkompassen/c216_222/index.html | ||
Thinking about anemometers with no moving parts- it may be possible to use a cheap pressure sensor as a pitot tube, with a 360 degree cowling that funnels horizontal moving air upwards into the sensor (picture two smooth funnels inserted into each other). An apparently cheap & suitable sensor for Arduino is: http://www.coolcomponents.co.uk/catalog/product_info.php?cPath=36_68&products_id=739 Coupled with a GPS chip to get SOG & COG, apparent and real wind speed could be directly output in NMEA0183 format. Add wind direction and done. | Thinking about anemometers with no moving parts- it may be possible to use a cheap pressure sensor as a pitot tube, with a 360 degree cowling that funnels horizontal moving air upwards into the sensor (picture two smooth funnels inserted into each other). An apparently cheap & suitable sensor for Arduino is: http://www.coolcomponents.co.uk/catalog/product_info.php?cPath=36_68&products_id=739 Coupled with a GPS chip to get SOG & COG, apparent and real wind speed could be directly output in NMEA0183 format. Add wind direction and done. | ||
Line 119: | Line 125: | ||
- | to-do: | + | ====== to-do: ====== |
* replace fuel-injector sleeve o-ring | * replace fuel-injector sleeve o-ring | ||
+ | * once per year grease lubricate stuffing box | ||
* replace spreader end covers | * replace spreader end covers | ||
* widen holes through "german solution" and spray rail to reduce friction on main & spinnaker halyards | * widen holes through "german solution" and spray rail to reduce friction on main & spinnaker halyards | ||
Line 131: | Line 138: | ||
* install new backstay adjuster | * install new backstay adjuster | ||
* lengthen/add loop to secondary bilge pump line | * lengthen/add loop to secondary bilge pump line | ||
- | * replace faucet & sink in head | + | * [[rini:iw31#faucet_replacement|replace faucet & sink in head]] |
* re-seal windows | * re-seal windows | ||
* sew new curtains and install new curtain rods | * sew new curtains and install new curtain rods | ||
Line 145: | Line 152: | ||
* replace cockpit drain hoses and clamps | * replace cockpit drain hoses and clamps | ||
* repair engine instrument panel warning lights, switches, and alarm | * repair engine instrument panel warning lights, switches, and alarm | ||
- | * add anchor light if possible (pull an old cable down with two cables in its place?) | + | * add anchor light if possible (pull an old cable down with two cables in its place? or wait until season end and bring the mast down) |
+ | * fix cables inside mast to something, they sway too much | ||
* replace masthead lamp with LED | * replace masthead lamp with LED | ||
* replace motor lamp with LED | * replace motor lamp with LED | ||
Line 172: | Line 180: | ||
* add sea-cock to bilge through-hull? | * add sea-cock to bilge through-hull? | ||
- | on-going | + | ====== on-going ====== |
* change oil & filter (done 9/7/2011) | * change oil & filter (done 9/7/2011) | ||
- | done: | + | ====== done: ====== |
* replace water tank (maybe a smaller tank would have been better) | * replace water tank (maybe a smaller tank would have been better) | ||
* mount water pump | * mount water pump | ||
- | * mount deck-block to better route main & spinnaker halyards back to cockpit | + | * mount deck organizer to better route main & spinnaker halyards back to cockpit |
* un-seize current backstay adjuster | * un-seize current backstay adjuster | ||
* remove old stereo | * remove old stereo | ||
Line 187: | Line 195: | ||
* move last jib reefing block up on stanchion to reduce wear | * move last jib reefing block up on stanchion to reduce wear | ||
+ | ====== equipment needed: ====== | ||
+ | * <del>life ring</del> & <del>man overboard light</del> & <del>throw line</del> | ||
+ | * <del>flares, 3 white, 3 parachute?</del> | ||
+ | * LED Lamps | ||
+ | * panel mount compass<del>es</del> (danforth saturn dual-read) - single compass in the instrument panel means one less hole in the deck | ||
+ | * for jib conversions, Harken Unit 0 uses #6 (6/32" or 5 mm) luff tape: [[http://www.sailmakerssupply.com/prod_detail_list/62|www.sailmakerssupply.com]] or [[http://search.sailrite.com/category/furling-reefing-spinnaker-sock-sleeve-uv-sacrificial-sail-kits-projects|www.sailrite.com]] or [[http://sailcloth.co.uk/index.asp?selection=detailed&uid=15898&catref=Sail%20Accessories&InBox=Leech%20Line%20and%20Luff%20Tape&cct=12&TypeSearch=&subcat=Rope|sailcloth.co.uk]] | ||
+ | |||
+ | ====== Task break-down ====== | ||
+ | ===== Faucet replacement ===== | ||
+ | * replace last section of tubing to both faucets - need X size hose. | ||
+ | * install pressure switch | ||
+ | * install in-line disable/override switch |